The first step is to determine what your problem is and then area zeroing. Some printers display panels on the status of the printer to relay information, others can not. They have a series of LEDs or lights that blink or flash can be. In that case you determine what the blinking lights are a sign for the printer will need some reference material. Some more advanced printer failure code, or error log that is what will keep track of past errors will have the ability to maintain. The printer will provide a lot of useful information on the history. The log is on the printer or printer seen through the display panel can be printed.

If the printer is jamming jamming an area of the printer you should try to isolate the issue. The collection / feed area, the transportation sector (down drums), fuser or exit the area? Keep it simple, try this collection roller (s) in the field of cleaning. If the jamming is less frequent now, perhaps a new roller (s) will correct the problem. A different input (tray) use to try and see if the problem is specific tray. If the jam is being pulled in multiple separation roller pad and you should suspect sheets is due to enter the printer to prevent more than one sheet at a time are responsible for. Fuser paper getting stuck in the fuser is at fault most likely, sticky paper on the sensor, the film (sleeve) is being or just plain worn out heating.

Many printers have a recommended maintenance intervals. 100k, 200k or pickup, feed, separation roller, transfer roller between the replacement of the fuser assy 300k pages. Cycle printer or print pages that have passed through the warning when you change it and then getting close to time when it's time will be changed to keep track of.

Print quality problems can be caused by a few different things. Toner cartridge, fuser, transfer roller, or even laser scanner or printer as faulty power supply components. toner cartridges and fuser of a visual inspection can be an easy thing to check. Drum.These mark removal usually fairly simple page in vertical direction would correspond to a double fault or scratch marks to the investigation. The drum surface should be cleaned when it is removed from the printer after a print cycle. If not, there's the problem with the cartridge within the cleaning system. It will need to be replaced. Fixing film or scratch marks, or tears to the hot roller check. Then there will be corresponding points in the vertical direction down the page. Either they failed visual inspection should be replaced. A simple yet effective test test print from the menu to start and stop half way through the printer before it gets to the fuser. The prints show no defects in the process before it gets to fuser, to help you determine which one is the cause of your print defects.

Multipurpose tray 1 or tray works the best as you can see the media going into the printer. Other than the plain paper media, you must ensure that the appropriate settings to be used or smudging, smearing and streaking will occur as a label printer to transfer properly and fuse cover, or Transparency toner is unable to being used. Wavy lines of a faulty laser scanner as other reasons. Black or a faulty power supply, DC controller, laser scanner assembly, or even empty pages of a formatter. Formatter and the engine running remove the test, usually a line test pattern will help you as a possible cause of the failure to eliminate formatter. Most HP laser printers (Canon Engine) is a test facility, DC controller or ECU (engine control unit) will print a microswitch which is constructed in standalone without formatter installed. DC controller or ECU usually cover where to stay you will have access to the test using a small hole. A small, thin non-conductive tools (plastic, wood) is the best cover microswitch to activate the hole test.Inserted use this to print a single page test. Holding down the switch on some printers will generate a continuous test.






http://www.kicktime.org/user/sandrn88


http://www.labforculture.org/en/mylabforculture/myprofile


http://www.livestrong.com/profile/sandrn88/


http://www.mocpages.com/home.php/74961


http://www.moviecentral.ca/members/sandrn88/default.aspx


http://www.myoats.com/users/Ramdin22


http://www.photosig.com/go/users/view?id=354146


http://www.pp2g.com/Members/ramdin22/aboutme


http://www.programmersheaven.com/user/sandrn88/


http://www.reciperate.com/sandrn/profile/


http://www.retaggr.com/Page/sandrn


http://www.routeyou.com/user/view/113095/userprofile.en


http://www.shreveporttimes.com/apps/pbcs.dll/section?category=PluckPersona&U=5e0302d8be0a4a148b0b75011548396c&plckPersonaPage=BlogViewPost&plckUserId=5e0302d8be0a4a148b0b75011548396c&plckPostId=Blog%3a5e0302d8be0a4a148b0b75011548396cPost%3adb47f202-6675-47b4-8823-56033b50da6c&plckBlogItemsPerPage=5


http://www.ted.com/profiles/905884


http://www.thekartel.com/my-profile/100246292-sandrn88.html


http://www.thepoint.com/users/sandrn88/profile


http://www.trulia.com/voices/profile/Home_Buyer-USA_Mobile_AL-1998463/


http://www.unnamedsite.com/user/sandrn88


http://www.wearewhatwedo.org/actions/view/2241/


http://www.wellsphere.com/aging-senior-health-article/sandrn88/1418063


http://www.worldsings.com/user/blogs/view/name_ramdin22/id_11858/


http://www.yobi.tv/ramdin/profile


http://www.youthnoise.com/user/ramdin22/blog/view/55380


http://www.zoji.com/987244


https://support.mozilla.com/en-US/user/394242